All products

El.vadi

Two-Lamp wiring kit for Lazer Lamps High Performance LED lights. The setup is quick, easy, and reliable with 2-pin Deutsch connection and no configuration procedures. The kit features a 12V relay (in waterproof housing), fuse, a battery terminal at one end, and 6.5m of flex on the lamp cable, and allows for the operation of Lazer products either in parallel with the standard lighting on the vehicle, and/or via an independent switch which can be mounted inside your vehicle.
All Lazer lamps are sold with a pre-wired female connector attached to the male connector of the lamp harness, to facilitate wiring in to your vehicle system.
Compatible with:
Linear-24 Flood
Utility-25
Utility-25 MAXX
Utility-45
Utility-50
Utility-80 HD (Heavy Duty)
RP Spot

Specifications:
6.5m cable lengths
Includes 12V relay and 20 amp fuse
Relay holder approved to IP53 when mounted in a vertical (upright) orientation
2-pin deutsch connections
Includes on/off switch for independent operation
Braided cable sections for added protection in engine bay

Stock: > 1 pcs.

Rezerves ritenis un instrumentu komplekts

RR5x112x57.1 125/70R18 kpl - spare wheel - dock and tool set.
- Size: 125/70R18.
- Distance between bolts: 5 x 112mm x 57.1mm.
В комплект:
- spare wheel
- a trapezoidal jack with a ratchet mechanism and a case for its storage,
- telescopic wheel wrench, extendable (up to 50 cm), with four heads: 17, 19, 21, 23 mm,
- a case for a wheel, equipped with a velcro fastener for fastening to the floor of the trunk,
- 1 pair of work gloves.

Stock: 0 pcs.

Dubļu aizsargi (kompl.) SKODA SUPERB III

Mud flaps: SKODA SUPERB III B8 2015-2019
The mud flaps effectively protect the underbody and bumpers against excessive dirt. In addition, they also enormously reduce dangerous road chippings and water spray.
Color: matte black.
Installation is made on regular seats of the car.
The main purpose: to protect the lower part of the car body from chipping, scratching.
With such model mud flaps on your car, you will get rid of such problems as:
- dirt on the bottom of the car,
- intense pollution of the side of the car, starting from the front wings,
- reduction of accumulated dirt or snow on the vehicle’s rapids.

Stock: 0 pcs.

Numura apgaismojums

License plate light bulbs for passenger cars-EP18
AUDI A1 2010 –
AUDI A3 8P 2004 – 2011
AUDI A4 B6 2000 – 2004
AUDI A4 B7 2004 – 2008
AUDI A6 C6 2005 – 2010
AUDI A7 2010 –
AUDI A8 2003 2009 USA
AUDI RS4 2006 – 2008
AUDI RS6 PLUS AVANT 2008 – 2009
AUDI Q7 2007 – 2012

Stock: 0 pcs.

Auto sakabes āķis VW PHAETON

Tow bar VOLKSWAGEN Phaeton, 4dv, 2002-
VERTICAL DETACHABLE TOWBAR

Stock: 0 pcs.

Eļļas filtra noņemšanas atslēga

Stock: 0 pcs.

Kit CRUZ Optiplus

Kit CRUZ Optiplus Volvo S60 sedan 4d (00-10)

Stock: 0 pcs.

Kapota aizsargs Ford Transit

Designed to protect from mechanical damages and scratches. Creates an upcoming air streams for less contamination of the wind shield and wiper blades. Aerodynamic design guarantee uplifting of an air flow as also it gives additional identity to your car. Made from firm acrylic glass, is absolutely safe to wash and don't need additional service. Deflector fixations design to exclude hood damaging and drilling.

Stock: > 1 pcs.

Kit Optiplus

Kit 6 supports CRUZ LCV Vivaro/Trafic (14--) - Talento/NV300 (16--) H1

Stock: 0 pcs.

Jumta šķērsstieņi

Car roof crossbars CRUZ CR 923-068
Made of galvanized steel
The design of the supports and covers is made of ABS.
Safer and more aerodynamic.
Innovative tension system built into the rods.
All types of accessories are easy to install.
If desired: a set of 4 anti-theft locks (code 932-014-15).
Included: 3 pcs.

Stock: 0 pcs.

Dubļu aizsargi (kompl.) LEXUS CT 200h

Mud flaps: LEXUS CT 200h 2014-2022
The mud flaps effectively protect the underbody and bumpers against excessive dirt. In addition, they also enormously reduce dangerous road chippings and water spray.
Color: matte black.
Installation is made on regular seats of the car.
The main purpose: to protect the lower part of the car body from chipping, scratching.
With such model mud flaps on your car, you will get rid of such problems as:
- dirt on the bottom of the car,
- intense pollution of the side of the car, starting from the front wings,
- reduction of accumulated dirt or snow on the vehicle’s rapids.

Stock: 0 pcs.

Auto sakabes āķis Toyota Sienna III

Toyota Sienna III 2011-2020
Version: USA and 4x4

Semi-automatic towbar
Mechanism with quickly demountable ending

Stock: 0 pcs.

Auto sakabes āķis Toyota Sienna III

Toyota Sienna III 2011-2020
The towbar is original, designed for a specific model.
-Included is everything necessary for installation.

Stock: 0 pcs.

Rezerves ritenis un instrumentu komplekts

RR5x114.3x66.1 145/80R18 kpl - spare wheel - dock and tool set.
- Size: 145/80R18.
- Distance between bolts: 5 x 114.3mm x 66.1mm.
В комплект:
- spare wheel
- a trapezoidal jack with a ratchet mechanism and a case for its storage,
- telescopic wheel wrench, extendable (up to 50 cm), with four heads: 17, 19, 21, 23 mm,
- a case for a wheel, equipped with a velcro fastener for fastening to the floor of the trunk,
- 1 pair of work gloves.

Stock: 0 pcs.

Rear box

Stock: > 1 pcs.

motora pārsega amortizātors

BONNET STRUT KITS Forget about dirty hands and clothes with RIVAL bonnet assist kits and make the opening of tailgate much more comfortable with RIVAL tailgate assist kit built on Stabilus dynamic gas struts

KEY FEATURES

Easy opening
Hands free operation
Clean clothes
Installation onto OE fitting points
Zink-flake coating to the fittings
Individual application of fittings and selection of gas strut for each car specific model.

Stock: 0 pcs.

Syringe-aspirator

SYRINGE 04277- 500 ml-
is a professional tool for extracting or replacing fluids, including brake fluid, coolant, oil or power steering fluid.
Designed primarily for adding or sucking out operating fluids from external tanks or tanks in machines or devices.
The set includes two hoses with lengths of 190mm and 197mm with a diameter of 5/16'' and 1/4''.
The piston has a seal made of high-quality rubber resistant to long-term exposure to grease and oils.
All seals are made with the greatest precision and allow for work under high pressure.
The syringe has a venting system that equalizes the pressure under the piston, which improves its efficiency and smoothness of work.
The semi-transparent cylinder allows for an accurate check of the fluid volume and the general condition of the fluid.
Ideal for use on quads, boats, agricultural equipment, industrial gearboxes, motor vehicles, caravans etc.
SPECIFICATION:
capacity: 500ml.
colour: transparent.
equipped with a quick connector.
designed for all operating fluids.
two hoses included (possibility to connect hoses to reach hard-to-reach places).

Stock: > 1 pcs.

Syringe-aspirator

Stock: > 1 pcs.

Fire extinguisher

Stock: > 1 pcs.

Izolācijas noņemšanas knaibles

Device designed for stripping insulation from cables.

Working range of the wire stripper: 0.2 - 6.0 mm² (10 - 24 AWG)

-multifunctional, reinforced device, with rubberized handle and hardened blades

-mechanism: frontal, automatic

-in the stripping process it automatically adjusts to the cross-section of the cable being worked on

-has an additional cutter and end crimper

-stripper with adjustable stripping length

-length: 205 mm

-weight: 0.30 kg

Crimping of connector lugs:

-insulated: 0.5 - 6 mm² (22-10 AWG),

-uninsulated: 4 - 6 mm² (12-10 AWG), 1.5 - 2.5 mm² (16-14 AWG), 05 - 1mm² (22-18 AWG).

HIGH QUALITY CONSTRUCTION

AUTOMATIC AMICO INSULATION STRIPER

-The INSULATION PULLER is a practical tool for quick and precise removal of insulation from single or multicore cables. To remove the insulation, insert the wire into the jaws so that it sits flush against the tool - then squeeze the handle.

-CABLE CUTTING TOOL - another function of the wire stripper is to cut wires. The 11 mm long blade is located between the handles of the tool. To cut a cable of similar or smaller width, simply place it between the blades and squeeze firmly.

-CONNECTOR END CAPSULE - With the tool, you can crimp insulated and non-insulated connector ends onto conductors of wires with a cross-section from 1.5mm2 to 6mm2. Simply insert the conductor with the stripped end and insert it into the connector terminal, then place it in the crimping location

-PRECEPTION OF PRESSURE FORCE + LIMITER - the device has a dial which is located under the jaws. With it you can adjust the amount of pressure on the insulation, so you don't have to worry about damaging the cable while working.

Stock: > 1 pcs.