All products

Towing loop

Stock: > 1 pcs.

Auto sakabes āķis SKODA OCTAVIA IV

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: > 1 pcs.

Auto sakabes āķis SKODA OCTAVIA IV

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: 0 pcs.

Auto sakabes āķis SKODA OCTAVIA IV

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Auto sakabes āķis VW GOLF VIII

The towbar is original, designed for a specific model.
-Included is everything necessary for installation.


VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: > 1 pcs.

Auto sakabes āķis VW GOLF VIII

The towbar is original, designed for a specific model.
-Included is everything necessary for installation.


Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Kompozītmateriāla motora aizsargs FORD TRANSIT

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Door stills TOYOTA RAV 4

Stock: 0 pcs.

Aizmugures bampera uzlika MAZDA CX 5

Do you often ship purchases, baggage, building materials, or travel with a dog?
✔️ Cover for the paint of the rear bumper (mechanical damage, scratches, abrasions, chips).
Is the rear bumper broken or damaged?
✔️ Ability to cover a damaged item.
The car is not a garage? Frequent visits to a car wash?
✔️ Protection against external factors (moisture, road salt, car wash products, etc.).
Want to enhance or highlight the look of your car?
✔️ Gives the car an exclusive character and unique appearance.
  The rear bumper trim Avisa is the perfect solution for your car, as it has both protective functions and looks great as a decorative element. Resistant to weather conditions (temperature -40 ° С / + 50 ° С) and visits to a car wash (moisture).
 This is not a typical chrome strip because it is made of polished stainless steel. Thanks to cleaning, its surface scales perfectly between hard chrome and a deep matte layer.
   The bent edge of the bumper is also closed in the cover plate through a specially profiled bend. It is fixed using a double-sided tape, which is located on all four edges of the plank.
  Attention! The product must be glued carefully, since it is impossible to repeat the installation after a single fixation.
  After installing the lining, you can easily load and remove luggage, and the scratched item now covers an exclusive accessory.
  You will receive the case in a sturdy packaging with assembly instructions 'Step by Step'. and 3M degreasing material. The kit also includes a tube Autosol (5 ml) - polishing and updating stainless steel. The excellent formula of the preparation provides a steel surface with a long-lasting gloss without scratches and a strong protective layer.

Stock: 0 pcs.

Adapteris

Code QS075 <-> QS075.
Adapter (adapter) electrical connection.
Designed for connecting cables on trailers and connecting lanterns with 2x075 square cables.
The CEGI QS tool is used.

Stock: > 1 pcs.

Knaibles elektriskiem savienojumiem

code CEGI QS .
Crimping tool for electrical connection for flat cable QS075xQS075.

Stock: > 1 pcs.

Pagrieziena lukturis

Turn signal yellow.

Stock: > 1 pcs.

Miglas lukturis

og lamp, LED, with 0.5 m cable.
- low energy consumption
- European E9 certificate.
- Electromagnetic compatibility - EMC, R10.
- The design of the lamp is resistant to shock and mechanical damage - PC glass.
- The lamp is protected against polarity reversal.
Flashlight parameters:
- supply voltage: 12-36 V.
- range of working ambient temperatures
from - 40 ° C to + 55 ° C.
- the lantern is sealed and weatherproof.

Stock: 0 pcs.

LED gabarīta lukturis

Yellow LED clearance lamp with a cable and a QS075 connector.
- 1 functional.
- low power consumption.
European E9 certificate.
Electromagnetic Compatibility - EMC
The design of the flashlight is shock-resistant.
Arbitrary polarization.
Flashlight functions:
- clearance light
Flashlight parameters:
- supply voltage: 12-36 V DC
- ambient operating temperature range from - 40 ° C to + 55 ° C
- the lantern is sealed and weatherproof.

Stock: > 1 pcs.

LED gabarīta lukturis

Yellow LED clearance lamp with an angle holder and cable.
1- functional LED lamp - low power consumption
European E9 certificate
Electromagnetic Compatibility - EMC
Impact resistant design
Arbitrary polarization
Flashlight parameters:
- supply voltage: 12-36 V DC
- ambient operating temperature range from - 40 ° C to + 55 ° C
- weather resistant lantern
- the lantern is sealed

Stock: > 1 pcs.

Tow bar MERCEDES G-Klasse

Stock: 0 pcs.

El.rozete

Ac socket PIN 7- metal,
-sometimes you need position GN gumija or GN gumija02392 - not included.

Stock: > 1 pcs.

Paklāji salonā gumijas VW GOLF III

High quality rubber mats tailored to the specific car model.
Good water and mud absorbing properties, indispensable in winter.
Colour: black
Advantages:
-areas exposed to wear additionally reinforced
-perfect fit
-odourless (mild vanilla scent)
-non-slip

Stock: 0 pcs.

Kinetiskā trose

Kinetic rope PLNK26X8XT
Dimensions: 26 mm x 8 m.
Minimum breaking load: 14600 kg.
Material: 100% nylon66
Benefits:
- extensibility at maximum load: up to 30%,
- reducing the impact on vehicle components,
- the possibility of a dynamic break,
- convenience when towing in confined spaces,
- resistance to chemicals and ultraviolet radiation,
- professional hand weaving.

Stock: > 1 pcs.

Kinetiskā trose

Kinetic rope PLNK24X8XT
Dimensions: 24 mm x 8 m.
Minimum breaking load: 12000 kg.
Material: 100% nylon66
Benefits:
- extensibility at maximum load: up to 30%,
- reducing the impact on vehicle components,
- the possibility of a dynamic break,
- convenience when towing in confined spaces,
- resistance to chemicals and ultraviolet radiation,
- professional hand weaving.

Stock: > 1 pcs.