All products

Trunk mats AUDI Q 3

Trunk mat - especial made mat for each model using 3D floor scan technology.
- High edges protects trunk interior from getting water and mud under the mat.
- No smell, is acid and oil neutral.
- Precise mat form prevents mat from sliding on floor surface.
- Easy washes with water or car shampoo.

Stock: 0 pcs.

Trunk mats AUDI A 1

Trunk mat - especial made mat for each model using 3D floor scan technology.
- High edges protects trunk interior from getting water and mud under the mat.
- No smell, is acid and oil neutral.
- Precise mat form prevents mat from sliding on floor surface.
- Easy washes with water or car shampoo.

Stock: 0 pcs.

Paklāji salonā auduma

Textile floor mats - made from special auto textile material. Good protection from dust and water. Easy to clean and wash. Ads additional sound isolation and makes your interior more elegant and comfortable.

Stock: 0 pcs.

Kniede plastmasas

Stock: > 1 pcs.

Kniede plastmasas

Stock: > 1 pcs.

Auto sakabes āķis HONDA CR-V

Options for electrical installation
- 12070526 - 7 PIN - oriģinal, 10.2018 >
- 21070526 - 13 PIN - oriģinal, 10.2018 >
- MP2D1 - 7 PIN - universal.
- MPWH3S-G13 - 13 PIN universal.



VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: 0 pcs.

Kartera aizsargs NISSAN QASHQAI

The crankcase is new, a copy of the original.
Prevents excessive wear on mechanical parts.
Protects against corrosion.
Installation in original places.
Made of high quality PVC, ABS.
Resistant to all types of working fluids and temperature extremes.
Very good quality at an affordable price.

Stock: 0 pcs.

Parkošanās sensors

The rear parking sensors with equipped display and an audio signal.
The device displays the distance to the obstacle and signals at which side of the vehicle the obstacle is. If the vehicle approaches an obstacle at a very short distance (20 cm), “STOP” will appear on the display screen.

Stock: 0 pcs.

Dzēriena turētājs

Universal car holder for drinks with the possibility of increasing the diameter of the holder, cans with a capacity of 250, 330 or 500 ml and any cups for coffee or tea can be put in.
Sets in radiator grille.

Stock: 0 pcs.

Aizsargstienis MERCEDES BENZ ACTROS

FRONT PROT.PIPE, LED,Ø60MM
50mm shorter on right side.
5 white + 2 amber LEDs
Material AISI304 (stainless steel)
- weight: 11,4 kg.
Product has certificate.
Installation time 60 min.
Instructions and necessary mounting brackets.

Stock: 0 pcs.

Vinčas āķis WLL 1.12T MBL 4.48T

Hook with eye and protection WLL1.12T MBL 4.48T yellow
Safety Ratio 4: 1
Tested for durability
Corrosion resistant, yellow paint
Material: steel
MBL = 4.48 t
WLL = 1.12 t
Length: 10 cm
Yellow color

Stock: > 1 pcs.

Vinčas āķis

Eye hook WLL 3 T MBL 12.0T, red.
Bollard pull up to 12 tons.
Safety Ratio 4: 1
Protected against corrosion.
Specifications
-Material: steel alloy
MBL = 12 t
WLL = 3 t
Color: red.

Stock: > 1 pcs.

Vinčas āķis

Eye hook, HE 6-8

Stock: > 1 pcs.

Winch hook

Stock: > 1 pcs.

Rear bumper cover VW TOURAN

Do you often ship purchases, baggage, building materials, or travel with a dog?
✔️ Cover for the paint of the rear bumper (mechanical damage, scratches, abrasions, chips).
Is the rear bumper broken or damaged?
✔️ Ability to cover a damaged item.
The car is not a garage? Frequent visits to a car wash?
✔️ Protection against external factors (moisture, road salt, car wash products, etc.).
Want to enhance or highlight the look of your car?
✔️ Gives the car an exclusive character and unique appearance.
  The rear bumper trim Avisa is the perfect solution for your car, as it has both protective functions and looks great as a decorative element. Resistant to weather conditions (temperature -40 ° С / + 50 ° С) and visits to a car wash (moisture).
 This is not a typical chrome strip because it is made of polished stainless steel. Thanks to cleaning, its surface scales perfectly between hard chrome and a deep matte layer.
   The bent edge of the bumper is also closed in the cover plate through a specially profiled bend. It is fixed using a double-sided tape, which is located on all four edges of the plank.
  Attention! The product must be glued carefully, since it is impossible to repeat the installation after a single fixation.
  After installing the lining, you can easily load and remove luggage, and the scratched item now covers an exclusive accessory.
  You will receive the case in a sturdy packaging with assembly instructions 'Step by Step'. and 3M degreasing material. The kit also includes a tube Autosol (5 ml) - polishing and updating stainless steel. The excellent formula of the preparation provides a steel surface with a long-lasting gloss without scratches and a strong protective layer.

Stock: > 1 pcs.

Tow bar AUDI Q 7

Stock: 0 pcs.

Engine, gearbox and radiator protection MET SUBARU FORESTER

Stock: 0 pcs.

Auto sakabes āķis HONDA CR-V

Options for electrical installation
- 12070526 - 7 PIN - oriģinal, 10.2018 >
- 21070526 - 13 PIN - oriģinal, 10.2018 >
- MP2D1 - 7 PIN - universal.
- MPWH3S-G13 - 13 PIN universal.



Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: > 1 pcs.

Tow bar HONDA CR-V

Options for electrical installation
- 12070526 - 7 PIN - oriģinal, 10.2018 >
- 21070526 - 13 PIN - oriģinal, 10.2018 >
- MP2D1 - 7 PIN - universal.
- MPWH3S-G13 - 13 PIN universal.



Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Tow bar HYUNDAI I 40

Options for electrical installation.
- 16080529 - 7 PIN - oriģinal, 09.2011 >
- 26080529 - 13 PIN - oriģinal, 09.2011 >
- 736916 - 7 PIN - oriģinal, 03.2012>
- 748627 - 13 PIN - oriģinal, 03.2012>
- MP2D1 - 7 PIN - universal.
- MPWH3S-G13 - 13 PIN universal.



VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: 0 pcs.