Instruments

Krusta ratatslēga

Cross ratchet 17x19x21x23

Stock: > 1 pcs.

Oil changing pan

Stock: > 1 pcs.

Clip removal tool kit

Tool set for removing car upholstery fastening clips, 4 pcs.
- Lever with cutouts at both ends: 220x20mm.
- Lever with cutouts at both ends: 185 x 20 mm.
- Lever with both blunt ends: 140x20 mm.
- Spoon lever: 160x22 mm.
- Material: hardened nylon, does not scratch or damage the upholstery.

Stock: > 1 pcs.

Āmurs

Safety hammer with hanger.
Hammer and safety knife in one.
A very useful and indispensable device in case of a collision or accident.
In modern cars, belt tensioners are triggered on impact, sometimes it is impossible to unfasten them. Thanks to this device, we can easily break the glass when the door is jammed or cut the seat belt, even if we have a limited range of motion.
Dimensions:
- total height approx. 17.5 cm
- width max. at the top about 7cm

Stock: > 1 pcs.

Oil filter wrench jaw type

Stock: > 1 pcs.

Riteņa atslēga

Wheel nut wrench 19мм

Stock: > 1 pcs.

Līmlenta - divpusēja

Double-sided adhesive tape - Scotch tape.
- Width: 12 mm
- Length: 5 m
- Thickness: 1 mm
- Acrylic, polymer tape

Stock: > 1 pcs.

Sprūdatslēga ar kvadrātu

>Mechanism with 45 teeth allows turning with 8 degrees minimum angle.
>Equipped with a flag switch, a quick-reset button and a holding ball.
>Material - chrome-vanadium steel CrV50BV30.
>It is hardened to hardness not less than 39HRC.
>It is chrome plated and matt finish to resist corrosion.

Stock: 0 pcs.

Uzsitējveseris

The head of sledgehammer is made from tool steel using hot forging (drop-hammers forging).
It is heat treated and phosphate plated to resist corrosion.
Sledgehammer handle is made from fibreglass.
It has high mechanical strength, water and heat resistance.
Equipped with rubber pads for softening the impact and easy gripping.

Stock: 0 pcs.

Plastmasas savilcēji

Plastic ties.
-4.8 x 380 mm

Stock: > 1 pcs.

Candle key

Trunk mat - especial made mat for each model using 3D floor scan technology.

Stock: > 1 pcs.

Portable lamp

Stock: 0 pcs.

Foot pump

Quickly demountable tow bar - removable vertically. Fast and comfortable detachment with met

Stock: > 1 pcs.

Atslēdznieka āmurs

HAMMER WITH A WOODEN HANDLE
Hammer head is made of 45 steel by the hot stamping method (forging hammers).
Hardness of the impact part - 45-45 HRC.
Square-shaped hammer head with flat and pointed impact parts.
Handle of the hammer is made of wood and covered with protective varnish.
Hammer head is protected from corrosion by chemical oxidation.

Stock: > 1 pcs.

Atslēdznieka āmurs

HAMMER WITH A WOODEN HANDLE
Hammer head is made of 45 steel by the hot stamping method (forging hammers).
Hardness of the impact part - 45-45 HRC.
Square-shaped hammer head with flat and pointed impact parts.
Handle of the hammer is made of wood and covered with protective varnish.
Hammer head is protected from corrosion by chemical oxidation.

Stock: > 1 pcs.

Regulējāmās plakanknaibles

>Made of chrome-vanadium steel by the hot stamping method (forging hammers).
>Equipped with comfortable rubber handles which protect the palm from slippage.
>Jaws induction hardened to 55-58 HRC.
>Protected against corrosion by phosphating.

Stock: 0 pcs.

Testeris

DC and AC voltage tester with LCD display, 12-250 V.
It is used to measure alternating voltage in the range of 12-250V with a frequency of 50-500Hz, to check the integrity of the cable and grounding.
Suitable for both professional electricians and occasional home use. The check is carried out by contact or induction method, i.e. when the tester approaches the installation being tested.
Specifications:
- LCD-screen displaying the results of measurements in the ranges up to 12, 24, 36, 55, 110 and 220 V.
- Additional LED signaling.
- Flat tip 2.9 mm wide - provides precise access to small elements.
- Power supply: 3 x LR41 (included)

Stock: > 1 pcs.

Mērlente

Dimensions:
9x0.145mm
length 5 m
Specification:
soft, non-slip handle
wristband
mounting clip
lock (side lock)

Stock: > 1 pcs.

Sānu griešanas knaibles

Side cutting pliers 58749. Precise work and quality materials ensure a long service life of the pliers. The blades are designed to cut soft and hard wire. The thin head allows you to work in hard-to-reach places. The handle is made of materials that increase comfort. Length 160 mm.

Stock: > 1 pcs.

Pliers

Stock: > 1 pcs.