Skid plates

Under engine cover aluminium MITSUBISHI L 200

Stock: 0 pcs.

Engine, gearbox protection MET FORD FOCUS

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Engine, gearbox protection MET LANDROVER RANGE ROVER EVOQUE

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Engine, gearbox and radiator protection MET HYUNDAI I 40

Stock: 0 pcs.

Engine and gearbox protection MET CHEVROLET MALIBU

Stock: 0 pcs.

Engine, gearbox and radiator protection MET KIA STONIC

Stock: 0 pcs.

Engine, gearbox and radiator protection MET HYUNDAI TUCSON

Stock: 0 pcs.

Engine, gearbox and radiator protection MET NISSAN X-TRAIL,RENAULT KOLEOS

Stock: 0 pcs.

Engine and gearbox protection MET OPEL INSIGNIA

Stock: 0 pcs.

Dzinēja un ātrumkārbas aizsargs MET CHEVROLET MALIBU,OPEL INSIGNIA

Code 2.0795.00
The Kolchuga engine compartment protection is made of high quality materials using modern technologies. It is based on cold-rolled steel 2mm or 3mm thick (depending on the car brand).
The protection has an anti-corrosion coating. It not only protects the crankcase from physical shock, but also the entire engine compartment - from water, dust and dirt. This significantly increases the service life of belts, rollers and other parts.
The protection has a unique shape that follows the shape of the underside of each car model, taking into account all its features and equipment. It is installed in the places provided by the car manufacturer, without additional drilling or welding, due to which the installation process is as simple as possible.
All necessary hardware is included.

Stock: 0 pcs.

Dzinēja un ātrumkārbas aizsargs MET FORD ESCAPE

Code 2.0848.00
The engine compartment protection Kolchuga is made of high quality materials using modern technologies. It is based on cold-rolled steel 2mm or 3mm thick (depending on the car brand).
The protection has an anti-corrosion coating. It not only protects the crankcase from physical shock, but also the entire engine compartment - from water, dust and dirt. This significantly increases the service life of belts, rollers and other parts.
The protection has a unique shape that follows the shape of the underside of each car model, taking into account all its features and equipment. It is installed in the places provided by the car manufacturer, without additional drilling or welding, due to which the installation process is as simple as possible.
All necessary hardware is included.

Stock: 0 pcs.

Engine, gearbox protection MET MERCEDES BENZ A-klasse (W177)

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Engine, gearbox protection MET OPEL INSIGNIA

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Engine, gearbox protection MET OPEL INSIGNIA

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Engine, gearbox protection MET LANDROVER DISCOVERY

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Dzinēja, ātrumkārbas aizsargs MET CITROEN BERLINGO/C 4 PICASSO,OPEL COMBO/GRANDLAND X

Code 2.0912.00
The engine compartment protection Kolchuga is made of high quality materials using modern technologies. It is based on cold-rolled steel 2mm or 3mm thick (depending on the car brand).
The protection has an anti-corrosion coating. It not only protects the crankcase from physical shock, but also the entire engine compartment - from water, dust and dirt. This significantly increases the service life of belts, rollers and other parts.
The protection has a unique shape that follows the shape of the underside of each car model, taking into account all its features and equipment. It is installed in the places provided by the car manufacturer, without additional drilling or welding, due to which the installation process is as simple as possible.
All necessary hardware is included.

Stock: > 1 pcs.

Engine protection CITROEN NEMO,FIAT FIORINO,PEUGEOT BIPPER

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection TOYOTA LAND CRUISER 200

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection HYUNDAI GETZ

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection HYUNDAI IX 55

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.