Skid plates

Under bumper cover

Stock: 0 pcs.

Kartera aizsargs CITROEN JUMPER, FIAT DUCATO, PEUGEOT BOXER

Crankcase guard - under the engine, set, a copy of the original.
Consists of 3 parts:
- middle part (RP150721),
- right side part (RP150715),
- left side part (RP150716).
Suitable for car models:
- CITROEN JUMPER II 2018 - 2021, diesel.
- FIAT DUCATO III 2018 - 2021, diesel.
- PEUGEOT BOXER II 2018 - 2021, diesel.
Crankcase protection effectively protects engine components from damage and extends their service life.
It is made of high quality HDPE material, which guarantees high mechanical and chemical resistance, as well as to temperature changes.

Stock: 0 pcs.

Kartera aizsargs CITROEN JUMPER, FIAT DUCATO, PEUGEOT BOXER

Crankcase guard - under the engine, middle part.
Suitable for car models:
- CITROEN JUMPER II 2018 - 2021, diesel.
- FIAT DUCATO III 2018 - 2021, diesel.
- PEUGEOT BOXER II 2018 - 2021, diesel.
Crankcase protection effectively protects engine components from damage and extends their service life.
It is made of high quality HDPE material, which guarantees high mechanical and chemical resistance, as well as to temperature changes.

Stock: 0 pcs.

Kartera aizsargs AL MITSUBISHI L200, FIAT FULLBACK

Crankcase protection - reducer protection OPA050ALU.
Designed for car models (all engine versions):
- MITSUBISHI L200, 2015-.
- FIAT FULLBACK, 2015-.
Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, the installation is carried out in the original mounts on the car frame.
The gear guard is only one part of the OPAK010ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL MITSUBISHI L200, FIAT FULLBACK

Protection of the gearbox - protection of the gearbox, OPA049ALU.
Designed for car models (all engine versions):
- MITSUBISHI L200, 2015-.
- FIAT FULLBACK, 2015-.
Material: aluminum thickness 6 mm.
The set of screws necessary for installation is supplied in a kit, the installation is carried out in the original mounts on the frame of the car.
Gearbox protection— this is only one component of the OPAK010ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL MITSUBISHI L200, FIAT FULLBACK

Crankcase protection - front / protection of the engine crankcase, axle and clutch rod OPA047ALU.
Intended for car models (for all engine versions):
- MITSUBISHI L200, 2015-.
- FIAT FULLBACK, 2015-.
Designed for installation on cars under the original factory bumper.
Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the OPAK010ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL MITSUBISHI L200, FIAT FULLBACK

Set of crankcase protection.
Intended for car models (for all engine versions):
- MITSUBISHI L200, 2015-.
- FIAT FULLBACK, 2015-.
Material: aluminum 6 mm thick.
The kit consists of:
- front crankcase protection (OPA047ALU)
- transmission protection (OPA049ALU)
- gear protection (OPA050ALU)
A set of mounting screws is supplied with the guards, and their assembly involves the use of factory holes and threads in the vehicle frame.

Stock: 0 pcs.

Kompozītmateriāla motora aizsargs FIAT PUNTO

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Kompozītmateriāla motora aizsargs FIAT 500X

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine, gearbox and radiator protection MET FIAT DOBLO,OPEL COMBO

Stock: 0 pcs.

Kompozītmateriāla motora aizsargs MITSUBISHI L 200

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection FIAT 500X

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Under engine cover FIAT STILO

Stock: 0 pcs.

Under engine cover FIAT STILO

Stock: 0 pcs.

Under engine cover FIAT STILO

Stock: 0 pcs.

Under engine cover FIAT STILO

Stock: 0 pcs.

Under engine cover FIAT PUNTO/IDEA,LANCIA MUSA

Stock: 0 pcs.

Under engine cover FIAT DOBLO

Stock: 0 pcs.

Under engine cover FIAT BRAVA/BRAV0

Stock: 0 pcs.

Under engine cover CITROEN JUMPER,FIAT DUCATO,PEUGEOT BOXER

Stock: 0 pcs.