Towbars

Auto sakabes āķis HYUNDAI KONA

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI KONA

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI KONA

Tow bar HYUNDAI KONA

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI SANTA FE

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI SANTA FE

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI SANTA FE

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Tow bar HYUNDAI SANTA FE

Stock: 0 pcs.

Tow bar HYUNDAI SANTA FE

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI SANTA FE

VERTICAL DETACHABLE TOWBAR

Stock: > 1 pcs.

Auto sakabes āķis Hyundai Santa Fe IV

Tow bar Vertically detachable (T60) Hyundai Santa Fe IV

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI STARIA

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Auto sakabes āķis HYUNDAI STARIA

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: 0 pcs.

Auto sakabes āķis HYUNDAI TUCSON IV

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Auto sakabes āķis HYUNDAI TUCSON IV

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: > 1 pcs.

Auto sakabes āķis HYUNDAI TUCSON IV

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: > 1 pcs.

Фаркоп INFINITI EX 30/37

Tow bar INFINITI EX 30/37
INFINITI FX

Stock: 0 pcs.

Auto sakabes āķis ISUZU D-MAX

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: > 1 pcs.

Auto sakabes āķis Iveco Daily Van 7/9/11m² 2014-

towbar beam Iveco Daily Van 7/9/11m² 2014-
You still need to purchase the beam fasteners for the set:
2067-MS4 - wheelbase 3000 + 3520 - 1 wheel.
or
2067-MS5 - wheel base 3520 - double wheels.
They are installed in the assembly places provided by the factory.
IMPORTANT !!! The towbar kit does not contain wiring.

Stock: 0 pcs.

Auto sakabes āķis Jaguar F-Pace

Tow bar Jaguar F-Pace

Stock: 0 pcs.

Auto sakabes āķis JAGUAR F-PACE

Tow bar with screw fixation.
ATTENTION !!! Electro installation kit not included.

Stock: 0 pcs.