All products

Auto sakabes āķis MG HS

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.

Stock: 0 pcs.

Auto sakabes āķis MG HS

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.

Stock: 0 pcs.

Auto sakabes āķis MG HS

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.

Stock: 0 pcs.

Auto sakabes āķis DACIA DUSTER / RENAULT DUSTER

VERTICAL DETACHABLE TOWBAR
Mounting of the detachable towbar

A. Before installing the detachable towball you must be sure it is in the `set` position. This can be seen from the color in the indicator window of the operation handle: this should be `red`. If this is not the case then push in the operation handle firmly to the end and then rotate the Handle - while keeping it pushed in - fully clockwise to its end position. The handle now will remain in this (`set`) position.
B. Remove the plastic weather cap and ensure that the housing is clear of any mud, gravel, road debris, i.e. Insert the detachable towbar into housing and move it up until the triangular pins are set into the corresponding recesses (left & right) of the housing.
While inserting the detachable towbar into the housing keep your hands away from the operation handle.
Next, pull the ball itself towards you while holding the towbar in the above position, i.e. triangular pins resting into their corresponding recesses (left/right) in the housing. The system then will automatically lock and the operation handle will turn to indication green and will also pop out about 5 mm. CHECK THIS !
Always check the indicator window in the operation handle shows`green` every time before you start towing.
If this is not the case, remove the towbar and start the mounting process again at point `A`.
C. The key operated lock is an anti theft device only. It is not involved with safe attachment Of the detachable towbar. It is safe to tow with the key operated lock unlocked as long as the towbar is correctly attached as described above.
D. Lock the towball by turning the key clockwise half a turn. Remove the key, after this the operation handle can no longer be pushed in and not be turned enough to activate the mechanism. If the towbar can be locked this also confirms that the towbar is correctly installed. It is essential that the indicator in the handle shows `green` prior to towing. Remember to remove the key from the lock before starting your journey. The towbar is then ready to be used.

Removal of the detachable towbar system.
A. Always remove/unhitch the trailer prior to removing the towball, and remove any accessories if they obstruct the locking system as well as detaching the safety cable.
B. Unlock the towball by turning the key anti-clockwise half a turn.
C. Hold the detachable towball with the left hand. Push the operation handle fully inwards and then whilst holding it pushed in turn the handle fully clockwise to its end position. The handle will remain in this position.
D. Let the detachable towball slide out of the housing while holding it in your hand to prevent it from falling onto the floor.
E. After removal of the towball the plastic weather cap should be attached to the housing.
F. When not in use keep the towball in safe, clean and dry place. If kept in the vehicle this must be located such that it is not free to enter the passenger compartment in the event of heavy braking, heavy cornering or in case of an accident.


Recommended electrical package for 13 PIN - 747572.

Stock: > 1 pcs.

Auto sakabes āķis DACIA DUSTER / RENAULT DUSTER

Semi-automatic towbar
Mechanism with quickly demountable ending

Body install:
1. Fix body of the mechanism to brackets by bolts M12x25mm.

Ball fastening:
1. To install the ball in mechanism push the lever down till resistance.
2. Slip the ball into body in this way so pins if the ball will be in nests of the body.
3. Let go the lever. It should return to initial position, this means correctly installed ball in the mechanism.
4. Put safety pin through lever's hole and bracket's hole. Correctly placed safety pin.

Ball unfastening:
1.To unfasten the ball take out the safety pin.
2.Push the lever down till resistance.
3.With fast move take out the ball. Let go the lever. It should return to initial position.
4.Put plug into the body. Plugs are in accessories of the towbar with quickly demountable ending.


Recommended electrical package for 13 PIN - 747572.

Stock: > 1 pcs.

Auto sakabes āķis DACIA DUSTER / RENAULT DUSTER

Tow bar with screw fixation. Tow bar constructed accordingly all European and car producer standards. Installs accordingly car producer mounting places. Kit contains all necessary parts for installation.
ATTENTION !!! Electro installation kit not included.
Recommended electrical package for 13 PIN - 747572.

Stock: > 1 pcs.

Wind deflectors Volvo XC90

Stock: > 1 pcs.

Mazgāšanas sūklis

Soft microfiber, mesh and fine chenille sponge, 23x12x6 cm

Stock: > 1 pcs.

Tējkanna

The kettle is powered by 24V direct current (DC) and is intended for use in vehicles, boats and camping. It can be connected to DIN and EURO sockets. Before use, make sure that the power output of the electrical outlet is suitable for the kettle. Use: 1. Fill the kettle with water between the MIN and MAX marks. 2. Plug the kettle into your vehicle's socket and turn it on. 3. After the water is boiled, the kettle will turn off automatically. 4. Make sure the appliance is cool before storing it. Important! When you do not use the kettle for a long time, it is recommended to clean it with a damp cloth and dry it. In case of damage, consult a professional service for repair. If a fuse blows, replace it with another of the same rating. 1. Do not turn on the kettle without water! 2. Avoid using near flammable liquids or gases! 3. Do not use the device if any part is damaged! 4. Never leave the kettle unattended when it is switched on! 5. Keep it away from children and pets! Always be careful when children or pets are near the kettle, especially when the water inside is hot! Technical specifications: Capacity: 500ml. Voltage: 12-24V DC. Fuse: 20A. Amperage: 11A. Power: 150-200W. Dimensions: 16.5 x 15 x 18.5 cm. Weight: 567gr.

Stock: > 1 pcs.

Mobīlā telefona turētājs

WAYME Gravity Air Inlet Holder, Graphite
Practical and solid phone holder mounted on the air intake grille. Allows multi-angle adjustment with a rotating ball. Automatic gravity locking and unlocking - one-handed operation.
Minimum phone width: 65mm
Maximum phone width: 85mm

Stock: > 1 pcs.

Mobīlā telefona turētājs

WAYME Gravity Air Inlet Bracket, Red
Practical and solid phone holder mounted on the air intake grille. Allows multi-angle adjustment with a rotating ball. Automatic gravity locking and unlocking - one-handed operation.
Minimum phone width: 65mm
Maximum phone width: 85mm

Stock: > 1 pcs.

Mobīlā telefona turētājs

Practical and solid suction cup mount. Allows you to change the length and inclination of the arm and multi-angle adjustment with a rotating ball. Gravity locking and unlocking - one-handed operation.

Minimum phone width: 65mm

Maximum phone width: 85mm

Stock: > 1 pcs.

Mobīlā telefona turētājs

Practical and solid phone holder mounted on the air intake grille. Allows multi-angle adjustment with a rotating ball. Automatic gravity locking and unlocking - one-handed operation. The holder is equipped with a USB C port, enabling inductive charging of the phone.
Minimum phone width: 65mm
Maximum phone width: 85mm

Stock: > 1 pcs.

Mobīlā telefona turētājs

Gravity holder with wireless charger. Suction cup mount. Allows to change the length and inclination of the arm and multi-angle adjustment of the rotating ball. Gravity locking and unlocking - one-handed operation.
Minimum phone width: 65mm
Maximum phone width: 85mm
Specification:
-USB-C port
-Input: 5V–3A 9V–2A 12V-1.5A 18W
-Output: 15W [MAX]

Stock: > 1 pcs.

Antena

20 cm braided antenna mast, 5 mm thread

Stock: > 1 pcs.

Antena

9 cm rubberized antenna mast with 3 adapters: 5, 6 and 7 mm

Stock: > 1 pcs.

Antena

Antenna mast 17 cm, rubberized, with 2 adapters: 5 and 6 mm

Stock: > 1 pcs.

Rezerves ritenis un instrumentu komplekts

RR155/90 R18 5x120x74.1 kpl - spare tire - temporary spare wheel and tool kit.
- Size: 155/90 R18.
- Distance between bolts: 5x120x74.1 mm.
Included:
- spare tire - temporary spare wheel,
- trapezoidal jack with ratchet mechanism and case for its storage,
- telescopic wheel wrench, retractable (up to 50 cm), with four heads: 17, 19, 21, 23 mm,
- wheel cover equipped with Velcro fastener for fastening to the trunk floor,
- 1 pair of work gloves.

Stock: 0 pcs.

Bagāžnieka šķērsstieņi

Roof rack
- for Volkswagen Caddy 2010-2015, 2015-2020
- Silver crossbars, length 86/86 cm
- Permissible load 75 kg
- Attachment point: Factory attachment points
- Material: aluminum, reinforced plastic
- Included: crossbars - 2 pcs, fastening elements
- Maximum beam width: 70 mm

Stock: > 1 pcs.

Halogēnā auto lampa C5W 12V 5W

Halogen car bulb.C5W 41MM 12V 5W
- Voltage 5W/12V
Application:
- Interior lighting
- Globe lighting
- License plate lighting
The price is indicated for 1 piece.

Stock: > 1 pcs.