Towbars spare parts

Tow bar

Tow bar

Stock: 0 pcs.

Rezerves daļa piekabes āķim

Locking handle for GDW towbar.

Stock: 0 pcs.

Combination ball head

Trailer weight: 3500 kg
Ball diameter Ø 50 mm.
The flange is fastened with four screws (pitch 90x40 mm), with clamp
  equipped with a clamp. You can tow traditional trailers or trailers equipped with a drawbar with a loop.
The clamp provides additional protection against the uncoupling of the trailer.
The mechanism is intended for vans equipped with support beams with four holes (plate with two rows and a pitch of 90 x 40 mm).
It is certified for use in all countries of the European Union.

Stock: 0 pcs.

Piekabes āķa detaļa

740.043 towing hook with ball max: 3500kgs
Traction capacity approved 3.500 kg
Ball joint Ø 50mm.
2-hole fixation:
Center to center 90mm
Ø 25mm axle
D value: 17 kN
S value: 250 kg

Stock: 0 pcs.

Piekabes āķa skrūvju komplekts

Kit bolts for mounting the towbar hook.
-M12 x 75 mm.

Stock: > 1 pcs.

Sakabes āķa automāts

Mechanism for vertical towbar.
Before installing the ball, make sure it is prepared for this. This can be seen from the color of the indicator on the ballpoint pen. The indicator should be red. If not, press down firmly on the knob and turn it (while holding it down) clockwise until it reaches the end position. The handle should remain in this position.
Remove the bottom plug on the towbar beam protecting the inside of the body from contamination. Make sure the inside of the housing is free from dust, sand, dirt, etc. Insert the ball into the housing from below so that the protruding pins fit into the specially prepared places in the housing. Do not touch the handle while inserting the mechanism into the housing.
Then pull the ball towards you (the pins on the left and right sides should be in the grooves on the body). The mechanism should automatically block the ball, and the handle should turn so that a green color appears in the window on the handle, and the handle itself pops out by about 5 mm.
Always check that the color in the dial window is green before using the system. Otherwise, disassemble the balls and start over from the beginning.
The lock in the mechanism serves only as an anti-theft device. It is not an element affecting the safe use of the system. It is safe to use the towbar without a locked key lock if the mechanism is correctly installed as described above.
Close the mechanism lock by turning the key half a turn clockwise. Once the key has been removed, it is not possible to press and turn the handle, and therefore it is impossible to detach the ball. If the mechanism can be closed with a key, then the ball is installed correctly. The most important indicator is the flywheel window, which must be green before towing. Remember to remove the key from the lock before towing. The quick release ball system is now ready for use.

Stock: > 1 pcs.

Tow bar

Stock: 0 pcs.

Slēdzenes vāciņš

Cover lock for tow bar removed vertically.
keys included

Stock: > 1 pcs.

Hook

Stock: > 1 pcs.

Piekabes āķa gals

Special hook used for cars with American towbars.
It enables turning over, which facilitates the use on low and high towbars.

Stock: > 1 pcs.

Plāksne

Plate under contact socket

Stock: > 1 pcs.

Plāksne

Plate under contact socket

Stock: > 1 pcs.

Plāksne

Plate under contact socket

Stock: > 1 pcs.

Plāksne

Plate under contact socket

Stock: > 1 pcs.

Plāksne

Plate under contact socket

Stock: > 1 pcs.

Bung

Stock: 0 pcs.

Sakabes āķa gals.

weight - 3.7 kg.
- trailer weight - 3500 kg.
- vertical load - 150 kg.
-manufacturer- WESTFALIA.

Stock: 0 pcs.

Bung

Stock: 0 pcs.

Tow bar

Stock: 0 pcs.

Piekabes āķa gals ieskrūvējams

Hook tow bar with thread
-18 mm.

Stock: > 1 pcs.