Skid plates

Order by:
 
 
Kategorijas filtri:
Car brand
Product Code Price Number
Engine protection CITROEN JUMPER,FIAT DUCATO,PEUGEOT BOXER

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Z0632

Price: 329.00 €

Add to cart

View

Skid plate AL

Skid plate: transfer case, 6 mm Aluminium

Stock: 0 pcs.

2333.5712.1/6

Price: 330.00 €

Add to cart

View

Engine protection MERCEDES BENZ E-klasse (W212)

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Z1717

Price: 330.00 €

Add to cart

View

Kompozītmateriāla motora aizsargs NISSAN QASHQAI

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Z1934

Price: 330.00 €

Add to cart

View

Kartera aizsargs AL FORD RANGER

Crankcase protection for FORD RANGER(T6/T7), 2011- (for all engine versions).
Designed to protect the gearbox and reducer.
Mounting screws are supplied in the kit to use the factory holes and threads on the vehicle frame when assembling.
The transmission and reduction guard OPA042ALU is only one part of the crankcase guard set OPAK011ALU but can be used without the need to install other parts.

Stock: 0 pcs.

OPA042ALU

Price: 330.00 €

Add to cart

View

Kartera aizsargs AL MITSUBISHI L200, FIAT FULLBACK

Crankcase protection - reducer protection OPA050ALU.
Designed for car models (all engine versions):
- MITSUBISHI L200, 2015-.
- FIAT FULLBACK, 2015-.
Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, the installation is carried out in the original mounts on the car frame.
The gear guard is only one part of the OPAK010ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

OPA050ALU

Price: 330.00 €

Add to cart

View

Kartera aizsargs AL MITSUBISHI PAJERO V80

Crankcase protection - front / protection of the engine crankcase, axle and clutch rod OPA077ALU.
Intended for MITSUBISHI PAJERO V80, 2006- (for all engine versions).
Designed for installation on cars under the original factory bumper.
Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the OPAK022ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

OPA077ALU

Price: 330.00 €

Add to cart

View

Kartera aizsargs VW CADDY/ FORD CONNECT

VW CADDY/ FORD CONNECT-
Skid plate, engine, AL.
- weight 11 kg.
- installation 30 minutes.

Stock: 0 pcs.

840050

Price: 330.00 €

Add to cart

View

Engine protection BMW X3 (F25)

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Z0224

Price: 331.00 €

Add to cart

View

Kartera aizsargs AL TOYOTA LAND CRUISER 120

Crankcase protection - engine crankcase protection, OPA007ALU.
- For Toyota Land Cruiser J120/J125, 2002-2009 (long and short base).
- Material: aluminum 6 mm thick.
It is installed on cars with original factory bumper, cars with Z001 bumper require OPA027ALU crankcase protection.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the OPAK001ALU kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

OPA007ALU

Price: 335.00 €

Add to cart

View

Kartera aizsargs AL TOYOTA HILUX

Crankcase protection - gearbox/reducer protection , OPA028ALU.
- For TOYOTA HILUX VIGO, 2011-2015 (for all engine versions).
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
Gearbox/reducer protection is only one part of the OPAK014ALU/OPAK014ALU-A kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

OPA028ALU

Price: 335.00 €

Add to cart

View

Kartera aizsargs AL TOYOTA HILUX

Crankcase protection - gearbox/reducer protection , OPA043ALU.
- For TOYOTA HILUX VIGO, 2005-2011 (for all engine versions).
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
Gearbox/reducer protection is only one part of the OPAK002ALU/OPAK002ALU-A kit, but it can be used without the need to install other parts.

Stock: 0 pcs.

OPA043ALU

Price: 335.00 €

Add to cart

View

Dzinēja, ātrumkārbas aizsargs MET MERCEDES BENZ VIANO

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

2.1028.00

Price: 338.50 €

Add to cart

View

Engine protection TOYOTA AURIS

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Z2934

Price: 341.00 €

Add to cart

View

Kartera aizsargs AL FORD RANGER 2023-/VW AMAROK 2023-

SKID PLATES for tank
AL 5mm.

Stock: 0 pcs.

R23-R2305A-FT

Price: 345.00 €

Add to cart

View

Kartera aizsargs AL FORD RANGER RAPTOR

Crankcase guard rear part.
- Protects the gearbox.
- Material: Aluminum - 5mm.
- Weight 22 kg.
- Comes with everything needed for installation.
Only for FORD RANGER RAPTOR.

Stock: 0 pcs.

806983

Price: 345.00 €

Add to cart

View

Under engine cover aluminium FORD TRANSIT CUSTOM

Skid plate FORD TRANSIT CUSTOM 5mm aluminium.

Stock: > 1 pcs.

807456

Price: 345.00 €

Add to cart

View

Kartera aizsargs AL RENAULT MASTER

Aluminium engine skis plate for the new Renault Master 2024+ model year. Improve the protection of your car.

Technical data:
Material - AW5754,
Thickness - 5 mm,
Product approval - Products are valid according to UNECE R26/R61 legislation.

Stock: 0 pcs.

82861070

Price: 349.00 €

Add to cart

View

Kartera aizsargs VW CADDY

SKID PLATE, ENGINE, AL | FROM 2017 -
840629

Stock: 0 pcs.

840629

Price: 350.00 €

Add to cart

View

Dzinēja, ātrumkārbas un radiatora aizsargs MET TOYOTA TUNDRA/SEQUOIA

Code 2.0804.00
The engine compartment protection Kolchuga is made of high quality materials using modern technologies. It is based on cold-rolled steel 2mm or 3mm thick (depending on the car brand).
The protection has an anti-corrosion coating. It not only protects the crankcase from physical shock, but also the entire engine compartment - from water, dust and dirt. This significantly increases the service life of belts, rollers and other parts.
The protection has a unique shape that follows the shape of the underside of each car model, taking into account all its features and equipment. It is installed in the places provided by the car manufacturer, without additional drilling or welding, due to which the installation process is as simple as possible.
All necessary hardware is included.

Stock: 0 pcs.

2.0804.00

Price: 350.00 €

Add to cart

View