Skid plates

Engine protection AUDI A 8

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Under engine cover aluminium MITSUBISHI L 200

Stock: 0 pcs.

Kartera aizsargs AL Toyota Land Cruiser J90/J95

Crankcase protection - to protect the gearbox OPA074ALU.
- For Toyota Land Cruiser J90/J95, 1996-2002 (for petrol engines).
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the set (OPAK019ALU/OPAK020ALU) , but it can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL NISSAN NAVARA /PATHFINDER

Crankcase protection - for the protection of the reducer, OPA066ALU.
Designed for car models (all engine versions):
- NISSAN NAVARA (D40) /PATHFINDER (R51), 2005-2010.
- NISSAN NAVARA (D40) /PATHFINDER (R51), 2010-2014.
Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The reducer guard is only one part of the OPAK016ALU kit, but it can be used without the need to mount other parts.

Stock: 0 pcs.

Engine protection SSANGYONG REXTON

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection NISSAN PATROL

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Kartera aizsargs AL JEEP WRANGLER

Crankcase protection- reducer protection, OPA088ALU.
- JEEP WRANGLER, 2018- (for engines 2.0L, 2.2L).
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The reducer protection is only one part of the crankcase guard kit (OPAK025ALU) but can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL Toyota Land Cruiser J90/J95

Crankcase protection - to reducer protect OPA015ALU.
- For Toyota Land Cruiser J95, 1996-2002(long versions), for diesel engines.
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the set(OPAK003ALU/OPAK013ALU) , but it can be used without the need to install other parts.
To install the gearbox protection on the short version of Toyota Land Cruiser J90, it is necessary to purchase a protective rail (OP062MET) in addition to it.

Stock: 0 pcs.

Kartera aizsargs AL Toyota Land Cruiser J90/J95

Crankcase protection - to protect the gearbox OPA014ALU.
- For Toyota Land Cruiser J90/J95, 1996-2002 (for diesel engines).
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The crankcase guard is only one part of the set(OPAK003ALU/OPAK013ALU) , but it can be used without the need to install other parts.

Stock: 0 pcs.

Kartera aizsargs AL Toyota Land Cruiser J95

Crankcase protection - to protect the gearbox, OPA075ALU.
- For Toyota Land Cruiser J90/J95, 1996-2002 (long version), for gasoline engines.
- Material: aluminum 6 mm thick.
The set of screws required for installation is supplied in the kit, installation is carried out in the original mountings on the car frame.
The gear guard is only one part of the kit (OPAK019ALU/OPAK020ALU) but can be used without the need to mount other parts.
To install the gearbox protection on the short version of Toyota Land Cruiser J90, it is necessary to purchase a protective rail (OP062MET) in addition to it.

Stock: 0 pcs.

Engine, gearbox and radiator protection MET FORD TRANSIT 2019-

Stock: 0 pcs.

Dzinēja, ātrumkārbas un radiatora aizsargs MET FORD TRANSIT 2022-

Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: 0 pcs.

Dzinēja, ātrumkārba, sadales kārba, radiators aizsargs MET VW AMAROK

Engine, gearbox, transfer case.
Only V-3,0 TDI.
Metal protection made from 2mm steel.
Is covered by layer of zinc, paint and varnish.
All necessary installation screws and brackets are included.

Stock: > 1 pcs.

Engine protection BMW 3 (E46)

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection FORD TRANSIT

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Under engine cover aluminium FORD TRANSIT

Stock: 0 pcs.

Engine protection CHRYSLER TOWN & COUNTRY/DODGE CARAVAN

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine, gearbox and radiator protection MET SKODA OCTAVIA A8

Stock: 0 pcs.

Engine protection AUDI A 8

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.

Engine protection FORD TRANSIT

Engine protection. Made of composite material using the most modern technologies.
Ensures the safety of the engine and its units for any shocks.
Fully protects the engine compartment from moisture, salt, snow and dirt.
Unlike metal protections, it absorbs well the impact and at the same time does not receive residual plastic deformations (dents), which subsequently will inevitably lead to damage to the engine or its units.
Protection is attached only to the supporting elements - side members, front and rear beam.

Fastening elements of protection are also fuses. With a strong dynamic impact, exceeding the strength of the side members, the protection comes unfastened and remains on the obstacle, while protecting the entire bottom of the vehicle from above above the vehicle protection from damage. In this case, the protection itself in such cases is destroyed very rarely. As a rule, it is put back using new fastening elements.
These fasteners also perform another very important task - they ensure the requirements of passive safety according to the EURO NCAP norms. With a strong frontal impact protection is detachable and allows the engine to freely go under the vehicle interior.

Stock: 0 pcs.